| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
| |
ao_play() can fail; in that case a negative error code is returned.
This error code is returned by write_to_ao() in turn. The function
fill_audio_out_buffers(), which calls write_to_ao(), doesn't check for
any error codes, and will likely trigger the assertion following the
function call. Change write_to_ao() to return 0 on failure to hopefully
prevent crashes when AOs fail.
|
| |
|
|
|
|
| |
The language string was dynamically allocated, which completely fails
if the cache is forked (which it usually is). Change it back to a fixed
length string, like the original code had it.
|
| |
|
|
|
|
| |
On reasonable systems, these types were the same anyway. Even on
unreasonable systems (seriously, which?), this may reduce potential
breakage.
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
The --start and --end switch now accept a chapter number. The chapter
number is prefixed with '#', e.g. "--start=#2" jumps to chapter 2.
The chapter support might be able to replace --chapter completely, but
for now I am not sure how well this works out with e.g. DVDs and BDs,
and a separate --chapter option is useful interface-wise.
(This was supposed to be added in 51503a, but apparently the fixup
commit adding it was lost in a rebase. This might also be the reason
for the mess-up fixed in 394285.)
|
| |
|
|
|
|
|
|
|
|
| |
Make demux_lavf not error out if no video or audio track is present.
This allows opening subtitle files with the demuxer.
Improve the test whether subtitles read from demuxers must do explicit
packet reads. (I'm not sure whether always doing these reads could have
bad effects, such as reading too many audio and video packets at once,
so be conservative.)
|
| |
|
|
|
|
| |
The computation for the A/V sync value was inside print_status(). Move
it into its own function; this makes things simpler and gets rid of some
minor dead code.
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The --keep-open option causes mpv not to close the current file.
Instead, it will pause, and allow the user to seek around. When
seeking beyond the end of the file, mpv does a precise seek back to
the previous last known position that produced video output.
In some corner cases, mpv might not be able to produce video output at
all, despite having created a VO. (Possibly when only 1 frame could be
decoded, but the video filter chain queues frames. Then a VO would be
created, without sending an actual video frame to the VO.) In these
cases, the VO window will not redraw, not even OSD.
Based on a patch by coax [1].
[1] http://devel.mplayer2.org/ticket/210#comment:4
|
| |
|
|
|
|
|
|
|
|
| |
sub_remove remove an external subtitle track, for whatever this may be
needed.
sub_reload removes and re-adds an external subtitle track.
Also rename sub_load to sub_add, because that seems to be more in line
with sub_remove.
|
| |
|
|
| |
Makes it less annoying to free the sub_data.
|
| |
|
|
|
| |
Similar to --volume. Takes this as opportunity to move the variable
corresponding to --volume into MPOpts.
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Rename the -ss option to -start, and -endpos to -length. Add a -end
option. The -end option always specifies an absolute end time, as
opposed to -endpos/-length.
All these options (--start, --end, --length) now accept relative times.
Percent positions (e.g. "--start=30%") are interpreted as fractions of
the file duration. Negative times (e.g. "--start=-1:00) are interpreted
relative to the end of the file. Chapters (e.g. "--start=#3") yield the
chapter's time position.
The chapter support might be able to replace --chapter completely, but
for now I am not sure how well this works out with e.g. DVDs and BDs,
and a separate --chapter option is useful interface-wise.
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Using --loop=inf on an unseekable file would put mpv (and all other
mplayers as well) into an endless loop, trying to seek to the start of
the file on each playback loop iteration. When the seek fails, playback
simply remains in the at-end-of-file state, and tries to issue a new
seek command for looping.
Fix by checking if the seek command fails, and abort looping in this
case. For that, queue_seek() is replaced with seek(). Due to the
circumstances, these two calls happen to be equal in this case: the
seek is absolute (i.e. no seek coalescing done), and the execution of
queued seeks is right after the loop code anyway.
|
| | |
|
| |
|
|
|
| |
av_noreturn is a rather recent addition to libavutil, and defining it
ourselves is trivial and makes playing compatibility games easier.
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Finish renaming directories and moving files. Adjust all include
statements to make the previous commit compile.
The two commits are separate, because git is bad at tracking renames
and content changes at the same time.
Also take this as an opportunity to remove the separation between
"common" and "mplayer" sources in the Makefile. ("common" used to be
shared between mplayer and mencoder.)
|
|
|
Tis drops the silly lib prefixes, and attempts to organize the tree in
a more logical way. Make the top-level directory less cluttered as
well.
Renames the following directories:
libaf -> audio/filter
libao2 -> audio/out
libvo -> video/out
libmpdemux -> demux
Split libmpcodecs:
vf* -> video/filter
vd*, dec_video.* -> video/decode
mp_image*, img_format*, ... -> video/
ad*, dec_audio.* -> audio/decode
libaf/format.* is moved to audio/ - this is similar to how mp_image.*
is located in video/.
Move most top-level .c/.h files to core. (talloc.c/.h is left on top-
level, because it's external.) Park some of the more annoying files
in compat/. Some of these are relicts from the time mplayer used
ffmpeg internals.
sub/ is not split, because it's too much of a mess (subtitle code is
mixed with OSD display and rendering).
Maybe the organization of core is not ideal: it mixes playback core
(like mplayer.c) and utility helpers (like bstr.c/h). Should the need
arise, the playback core will be moved somewhere else, while core
contains all helper and common code.
|
